Can You Use A Boat With Bad Stringers? (2022)

If you neglect this step, you will likely have another repair job in a few years when the core material rots. Top: Active core of solid wood or plywood. Bottom: Inactive core of low-density foam or no no core. Drill 3/16″ holes 1″ apart over the rotted area. Can you use a bobby pin to unlock a door? how to unlock a door with a hole with a bobby pin.

Contents hide

1 Can you use a boat with rotted stringers?

2 How important are stringers in a boat?

3 How do you check a boat Stringer and transom?

4 Can you fiberglass over rotted wood?

5 What causes boat stringers to rot?

6 Do stringers attach to the transom?

7 Do fiberglass boats have wood in them?

8 Does contender use wood in their boats?

10 What causes soft spots on boats?

11 What does it mean when the stringers are wet?

12 Can you fix a rotted transom?

13 How long do transoms last?

14 How do I know if my boat has dry rot?

15 How do you treat rotted wood on a boat?

16 Does fiberglass bond to wood?

17 What wood should I use for boat stringers?

18 How much does Dryboat cost?

19 Does crownline use wood stringers?

20 Do fiberglass boats deteriorate?

21 Does fiberglass dry rot?

23 How good are Contender Boats?

24 What year did contender boats start?

25 What happens if transom is rotten?

26 How do I know if my bass transom is bad?

27 How thick should Plywood be on a boat floor?

28 How do you fix soft spots in fiberglass?

29 What kind of wood is used for boat decks?

30 How do you reinforce a transom?

31 What type of boat is most likely to have a planing hull?

32 Do transoms Flex?

Can you use a boat with rotted stringers?

If you neglect this step, you will likely have another repair job in a few years when the core material rots. Top: Active core of solid wood or plywood. Bottom: Inactive core of low-density foam or no no core. Drill 3/16″ holes 1″ apart over the rotted area.

How important are stringers in a boat?

The Stringers Looking at the bottom-support structure provides clues to the real quality of construction. A fiberglass laminate is very flexible, so all fiberglass boats rely on longitudinal stringers and athwartships frames and bulkheads to maintain the hull’s designed shape.

How do you check a boat Stringer and transom?

  1. Apply pressure downwards on the engine leg;
  2. Observe if the transom compresses around the engine bolts;
  3. Observe for cracking on the fibreglass around the engine bolts;

Can you fiberglass over rotted wood?

Fiberglass will bond to many different surfaces including wood, Styrofoam and even metal. Many times fiberglass is used to reinforce and protect wood. Fiberglass is a non corrosive waterproof material, that’s fairly easy to work with. … The mat will form and bond to the wood, creating a protective layer over the wood.

What causes boat stringers to rot?

If your stringers are exposed to bilge water frequently, they will need to be replaced on a periodical basis. They will start to rot, even if they are made from good quality wood that has been water-treated. Also look for staple marks. Water can get into these and rot the wood.

Do stringers attach to the transom?

You can continue the stringers over the transom and make them connect or, if you don’t want to do that, put brackets at the end of the stringers in the corners of the transom and hull. Either way, make sure these corners have a nice radius.

Do fiberglass boats have wood in them?

Fiberglass Boats. Most fiberglass boats have wood in them. … Sailboats travel more slowly and depend more on hull structure for strength, but even so they often have glass-encapsulated wood stringers, engine beds, and lots of balsa or plywood cored decks.

Does contender use wood in their boats?

While Contender Boats still uses wood in a few areas, like the transom and the anchor locker, it is high-grade marine plywood and is sandwiched between layers of vinylester resin. Stringers are of fiberglass composite.

How do you test a rotten transom?

Look for any signs of transom bowing or deformation. Look for any signs of the motor mounting bolts and washers being pulled into the transom. If the customer knows his boat, he will not have any issues with you to tug up and down on the bottom of the motor with the motor tipped fully up.

What causes soft spots on boats?

Soft spots on the deck are a sign of rotted and delaminated core materials. Although these sometimes can be repaired, more times than not soft deck sections are an indicator of what is below the deck: a wet or rotted stringer system. Another area of potential concern is the boat’s systems.

What does it mean when the stringers are wet?

Myth: Wet readings on stringers mean the boat hull is junk. If that were the case, then most every boat with wood stringers would be junked. The fact is, most have moisture levels which are higher than when the stringers were installed. Take care to prevent rot and the boat can live on.

Can you fix a rotted transom?

It’s difficult to repair a rotted I/O transom without removing the through-hull units, although it’s do-able. The key to repairing a rotted-out transom is gaining access to the wood inside of the transom. … It’s important because it allows at least some of the bad wood to be removed, and allows what’s left to dry out.

How long do transoms last?

On to fabricating the replacement transom: Most, if not all wooden transoms in smaller boats are made of plywood. From the looks of the transom in this boat, I would estimate a typical transom will last about 20 years or so before they need to be replaced.

How do I know if my boat has dry rot?

Take a look at all the wood you can—including under corners and crevasses—to see if there’s any evidence of dry rot. Look for any discoloration of the wood itself: if parts of the wood look different than the rest of it, then you’re looking at the potential for dry rot.

How do you treat rotted wood on a boat?

Always apply Totalboat penetrating epoxy to dry, clean, and unfinished wood. Remove contaminants by wiping the wood with acetone and a clean rag. Ensure that the surface is completely dry. Measure and mix resin and hardener in a plastic cup.

Does fiberglass bond to wood?

Fiberglass resin can seal wood to form a shell that protects the wood, and provides a smooth painting surface. It also fills in any imperfections. Glassing over wood requires a few precautions and techniques to ensure uniformity, strength and bonding.

What wood should I use for boat stringers?

You want wood that has a straight grain, free from knots or if there are knots, they should be very small and tight. Find some lumber that has a tight grain, with close annual ring spacing. It would also be wise to use a species that has good rot resistance and is easy to glue.

How much does Dryboat cost?

Dry StorageENCLOSED DRY STORAGE * Computed length under 35 ft$14.00/ft$15.00/ftMinimum Monthly Amount$290/mo.$310/mo.* Computed length 35 ft or more$14.50/ft$15.50/ftPontoon Boats OUTSIDE RACK (limited availability)$14.50/ft $11.75/ft$15.50/ft $12.75/ft

Does crownline use wood stringers?

This is one of the factors that makes the hulls heavier than their competition. Currently, Crownline does not use any wood at or below the waterline in its construction. … The hull, stringers, transom, and deck are all covered for the boat’s life for the original owner.

Do fiberglass boats deteriorate?

Fiberglass is very durable, and with proper maintenance and care, fiberglass boats can last for many decades. Fiberglass itself will not break down but instead will break down due to outside factors. Some factors that will affect break down are: Exposure to UV rays.

Does fiberglass dry rot?

Fiberglass is incredibly durable and generally speaking, it will not rot.

Are contenders unsinkable?

Review after review will confirm that the contender boats for sale are virtually unsinkable. The design is solid and even when there are cracks and bore holes in the wood, the vessels tend to hold up to the elements.

How good are Contender Boats?

Contender went on to make 32-foot, a 39-foot and a 30-foot stepped hull. “Our stepped hulls are the finest performing offshore boats available today,” says Neber. “Their fuel economy, seakeeping ability, soft ride, and safety in a following sea are incredible. … Good seakeeping is a driving force.

What year did contender boats start?

Joe Neber the President and Owner of Contender Boats founded the company in 1984. An avid saltwater sportsman, Joe has an undeniable passion for fishing and boating, which is evident by his work in resource conservation.

What happens if transom is rotten?

Bad rot will lead to totally deteriorated wood and a lot of flex in the transom when the outdrive unit is under load. If you’re not experiencing that, then your transom overall is probably okay. You can probe with a piece of stiff wire around the screw holes and see if there is any severe softness.

How do I know if my bass transom is bad?

Typically you will see the transom flexing under power, or flexing when applying pressure to the outboard (by hand). You may also see large stress cracks in the corners where the transom meets the sidewalls. For fiberglass you could take a core sample using a hole saw to see if the inner wood is wet and/or rotted.

How thick should Plywood be on a boat floor?

“Use a good grade 1/2 to 5/8 plywood (I used 3/4) you should cover the bottom side with fiberglass cloth, make sure you use a 24 to 36 grid pad to rough up the wood before laying your cloth down.

How do you fix soft spots in fiberglass?

You can repair this damage in a weekend. Use a palm sander to sand the weak spot below the level of the sound fiberglass surrounding the weakened area. Since the fiberglass has already thinned or cracked, you may sand all the way through the fiberglass in spots.

What kind of wood is used for boat decks?

Pressure treated pine is the most common and affordable type of wood commonly used for boat docks. The pros of using this material is the initial cost is the cheapest compared to other options. This material should last you 20 years or more with annual maintenance.

How do you reinforce a transom?

Apply epoxy to the edges of the outer fiberglass skin of the transom and over the heads of the screws holding the skin to the plywood, and lay a strip of fiberglass cloth over the epoxy. Once the fiberglass has cured, repeat this step until four layers of fiberglass and epoxy have been applied.

What type of boat is most likely to have a planing hull?

Flat-bottomed and vee-bottomed hull shapes act as planing hulls. Most small power-driven vessels, including personal watercraft (PWC), and some small sailboats have planing hulls, allowing them to travel more rapidly across the water.

Do transoms Flex?

The flex/movement in the transom should not be enough to transfer stress to that part of the boat. It is not an integral support of the transom.

Top Articles

Latest Posts

Article information

Author: Kieth Sipes

Last Updated: 12/06/2022

Views: 5936

Rating: 4.7 / 5 (47 voted)

Reviews: 86% of readers found this page helpful

Author information

Name: Kieth Sipes

Birthday: 2001-04-14

Address: Suite 492 62479 Champlin Loop, South Catrice, MS 57271

Phone: +9663362133320

Job: District Sales Analyst

Hobby: Digital arts, Dance, Ghost hunting, Worldbuilding, Kayaking, Table tennis, 3D printing

Introduction: My name is Kieth Sipes, I am a zany, rich, courageous, powerful, faithful, jolly, excited person who loves writing and wants to share my knowledge and understanding with you.